Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

SEM-ED analysis

A section of the film was removed from the bag and was immersed in liquid nitrogen. The section was then freeze-fractured and mounted on the SEM stage with the outside surface of the bag section facing downward. The sample was sputter coated prior to SEM/EDS analysis. Sputtering was performed to deposit approximately 20 nm of gold/palladium onto the sample. Double-sided conductive tape was used to ensure that the sample was sufficiently grounded to... [Pg.630]

The Atomic emission spectrometry (ICP-AES) results on the solids confirm the chemical purity of Py, Cp, Qz, Cal and Dol samples. The Po sample contains calcium which, after conversion into calcite, gives approximately 10wt% of this mineral. Sid sample contains 10.3 wt% Mn and 1.86 wt% Mg, in agreement with measurements using a Scanning Electron Microscopy coupled to Energy Dispersive X-Ray Spectroscopy (SEM-EDS) analysis again this explains the difference between the measured and theoretical density of the Sid powder. [Pg.328]

The limitation of an SEM-EDS analysis of minerals is that it cannot characterise the crystal structure of the minerals present. As a result it is difficult to determine some minerals types e.g. [Pg.27]

The SEM-EDS analysis produced a semiquantitative analysis of the elemental composition found in the samples. In spite of the presence of a number of heavy elements, organics were present in significant quantities. Consequently, the inorganic identification route of inductively coupled plasma-mass spectrometry (ICP-MS) was not pursued at this time. [Pg.35]

Cengiz, S. (2005). Reply to letter to the editor SEM-EDS analysis and discrimination of forensic soil. Forensic Sci. Int. 155, 225. [Pg.308]

On the other hand, when the content of sulfur in the gas was sufficiently high (1000-2(X)0 ppmv) for bulk nickel sulfide (NijSj) formation (ascertained by X-ray diffraction analysis), the distribution of sulfur in the catalyst bed was fairly even in different parts of the bed (Table 1) and also within catalyst particles. According to SEM/EDS analysis the content of sulfur on the surface ranged from 4.0 to 7.5 wt% and in the middle of particles from 5.3 to 9.3 wt%. However, nickel forms a liquid sulfide product at temperatures above 635 C [18, 19]. According to the SEM analysis of the firesh and spent catalyst particles, no liquid formation on the catalysts was detected. [Pg.474]

Table 2. Composition of white powder in the SO2 absorber by SEM-EDS analysis... Table 2. Composition of white powder in the SO2 absorber by SEM-EDS analysis...
Spectrometer (EDS). Quantification can be quite good if appropriate standards are used. The X-ray detector can be set to only detect and count X-rays that have energies within a narrow range. This output can then be used to generate elemental distribution maps, or line scans. Newer detectors with ultrathin windows can easily detect all elements with an atomic number of 5 (boron) or greater. Some applications of SEM-EDS analysis are given in the metallography chapter of this manual. [Pg.81]

In particular, it is possible to overlay the image with the EDS data - a technique known as elemental dot-mapping, widely used for SEM/EDS analysis (Figure 7.20). [Pg.608]

The aluminum bronze anode was covered by a thin, flaky oxide layer after each test (Figure 1.6.18). Pieces of this layer were always found on top of the frozen electrolyte - rather than deep inside it - suggesting that the oxide layer did not begin cracking until after electrolysis was stopped and the electrodes were raised out of the electrolyte melt. SEM-EDS analysis of anode flakes indicated that the anode film contained mostly CU2O and trace amounts of Ni, Fe, and Mn. [Pg.67]

Major elements Scanning Electron Microscopy/Energy Dispersive X-Ray (SEM/EDS) analysis (Camscan 4DV/Tracor TN 5500) (7) X-ray Fluorescence (XRF) analysis, melting technique (Siemens SRS 300). [Pg.126]

Fig. 3 (A),(B) SEM Images demonstrate the existence of semi anti-EGFR/GNPs with different magnifications (10000 x and 100000 x). (C) The SEM-EDS analysis of the element Au distribution of MBT2 cells... Fig. 3 (A),(B) SEM Images demonstrate the existence of semi anti-EGFR/GNPs with different magnifications (10000 x and 100000 x). (C) The SEM-EDS analysis of the element Au distribution of MBT2 cells...
CAR can be observed microscopically on double-sided PWBs using back lighting (Rig. 12). Subsequent scanning electron microscopy with energy dispersive x-ray spectroscopy (SEM/EDS) analysis shows that it contains copper and chloride (Fig. 13). A CAR sample was extracted and transmission electron microscopy (TEM) analysis was used to obtain electron diffraction data. Analysis of these results identify CAR as atacamite, Cu2(OH)3Cl (Ref 24). The Pourbaix diagram (Ref 25) (Fig. 14) of the cop-... [Pg.138]

Table. 3. Water—rock interactions deduced from SEM-EDS analysis and PHREEQE calculations... [Pg.80]

XRF analysis of the various size fractions showed Pb, Cu and Zn are concentrated in the finer fractions in soils both on and near the site. SEM-EDS analysis revealed that Pb and Cu in the coarser fractions were usually associated with fine particles in large agglomerations. It also revealed that even in the fine fractions, Pb and Cu contamination was not uniform, but was restricted to specific particles. Zn-rich areas were not located despite this metal having the highest concentration in the bulk soils. [Pg.260]


See other pages where SEM-ED analysis is mentioned: [Pg.610]    [Pg.213]    [Pg.33]    [Pg.280]    [Pg.308]    [Pg.308]    [Pg.197]    [Pg.410]    [Pg.383]    [Pg.413]    [Pg.672]    [Pg.707]    [Pg.780]    [Pg.497]    [Pg.1]    [Pg.292]    [Pg.324]    [Pg.162]    [Pg.497]    [Pg.82]    [Pg.960]    [Pg.58]    [Pg.301]    [Pg.174]    [Pg.73]    [Pg.334]    [Pg.155]    [Pg.139]    [Pg.140]    [Pg.332]   
See also in sourсe #XX -- [ Pg.280 ]




SEARCH



EDS

EDS analysis

SEM analysis

SEM and EDS analyses

© 2026 chempedia.info